Wi-Fi 6 vs Wi-Fi 7: does a Hong Kong office need to upgrade now?
GNS Engineering Team 3 min read
Wi-Fi 7 standards and products are now available, and clients keep asking whether this is the moment to replace the office wireless network. The answer depends on which generation you run today, and on whether the problem you have is coverage or speed. This article sets out what actually changed between the two standards, then why there is no rush to move everything to Wi-Fi 7.
1. What actually changed from Wi-Fi 6 to Wi-Fi 7
Wi-Fi 6 (802.11ax) uses 2.4 / 5 GHz, with a maximum channel width of 160 MHz and 1024-QAM. Wi-Fi 7 (802.11be) doubles the maximum channel width to 320 MHz, raises modulation to 4096-QAM, and adds Multi-Link Operation (MLO), which lets one client coordinate multiple wireless links to reduce latency. Multi-RU with puncturing also reuses a partly interfered channel instead of abandoning it whole.
2. The headline speed needs Wi-Fi 7 clients
This is the part that matters most. The numbers on a Wi-Fi 7 datasheet require a Wi-Fi 7 client, such as a phone, laptop or tablet, to be reached. Most offices today run a mix of devices bought over several years. Those devices connect to a Wi-Fi 7 access point without any trouble, but they negotiate at Wi-Fi 6 or 6E rates, with no MLO and no 320 MHz. A new access point does not make an unsupported device faster.
3. The coverage and approval cost of 6 GHz
Higher frequencies penetrate less. 6 GHz and 320 MHz perform well in open space, but in a typical Hong Kong office with many partitions and a large floor plate, the signal falls away faster than at 5 GHz. Keep the same number of access points and coverage can actually get worse. Getting value from 6 GHz usually means re-planning access point density and placement. In Hong Kong, the exact 6 GHz model must also meet OFCA type-approval and operating conditions.
4. The costs attached to a Wi-Fi 7 upgrade
The access point is only one link in the chain. To use Wi-Fi 7 properly, the switch and uplink should provide 2.5G or better, and a 6 GHz model must receive the power its specification requires. Replace only the access point and leave the power and cabling as they are, and most of the time the experience stays at Wi-Fi 6 levels.
5. What to do at this stage
Our advice is to survey first: measure coverage, device density and interference, then decide which areas genuinely fall short. If your Wi-Fi 6 or 6E system still holds up, there is no urgent case for replacing it; the real problems are usually a few dead spots or one unusually dense corner.
As of October 2026, our shop does not list a Wi-Fi 7 MikroTik model. The hAP ax² and hAP ax³ currently listed are dual-band Wi-Fi 6 models for 2.4 / 5 GHz and have no 6 GHz radio. We do not treat a standard name as a feature every product has: selection is explained by the actual model specification, stock and client support. The first site survey is free, and we will tell you which areas need attention before suggesting new hardware.
Frequently asked questions
Will a Wi-Fi 7 access point support our existing Wi-Fi 6 devices?
Yes. Wi-Fi 7 is backward compatible, so older devices still connect normally, but they run at the Wi-Fi 6 or 6E rates and features they support, with no MLO and no 320 MHz.
Will a Wi-Fi 6 access point bought today be obsolete soon?
Not necessarily. Wi-Fi 6 remains practical where it meets current client, coverage and bandwidth requirements. Wi-Fi 7 should be judged on the actual product specification, client support, site capacity and engineering cost, not on the generation label alone.
What else is needed besides new access points for Wi-Fi 7?
Check client support, switch and uplink capacity, power, and whether the exact 6 GHz model meets OFCA requirements. If any part of the chain is insufficient, real performance may remain below the Wi-Fi 7 specification.
How do we judge whether our office should upgrade?
Start with a free site survey measuring coverage, device density and interference. If the current system is still sufficient, we will recommend keeping it and addressing only the areas that fall short.
